Leading 10 usual forklift crashes ， forklift procedure must take notice of these issues ！.

Leading 10 usual forklift crashes ， forklift procedure must take notice of these issues ！.

Blog Article

Don't underestimate the forklift at the office. If the procedure is bad, there will certainly be serious accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost created casualties.
Instance 3: The size of the forklift cargo surpasses the allowable size of the course and holds on the roadside shelf, which practically causes an crash.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift motorist did not observe the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the workers illegally, the forklift vehicle driver does not put on the seat belt, the forklift lifter drops and the vehicle driver is crushed when the forklift rolls over.
Instance 7: The forklift motorist did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift operation need to focus on these matters ：.

Beginning.
1. Prior to starting, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale need to be safe prior to beginning.
3. When the forklift starts with a lots, the chauffeur should initially validate that the tons is secure and trustworthy.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the job website or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork has to not be raised too expensive, which will certainly influence the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released first. High-speed sharp turns are forbidden. High-speed doglegs will certainly create the vehicle to lose lateral security and topple. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is forbidden to brake unexpectedly while driving with tons unless there are unique conditions.
6. When the forklift is running, it must obey the traffic rules in the factory and should maintain a certain security distance from the car in front. .
7. When the forklift is running, the tons needs to remain in the lowest setting that does not impede the driving, and the gantry ought to be appropriately slanted back. The tons shall not be raised except when stacking or filling. .
8. The elevation of the lots need to not obstruct the motorist's sight. In special situations, when the item affects the forward vision, drive at a reduced rate when reversing.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it has to drive securely at a low speed when getting in the Stand-on Electric Pallet Stacker manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to stand on the fork to hold things and play a stabilizing function. .
12. If problems are located, they will certainly be repaired and reported in a prompt way, and they will never ever run with illnesses or hide them.

filling and dumping.
1. When fork-loading things, the distance in between the two forks need to be readjusted as needed to make the tons of the two forks balanced and not manipulated, and one side of the thing should protest the rack. .
2. It is restricted to deal with Stand-on Electric Pallet Stacker a single fork or utilize a fork top or pull. In unique circumstances, safety and security indication must be established to remind bordering pedestrians. .
3. In the process of packing and discharging items, the forklift has to be stopped with the brake. .
4. The rate of the lorry need to be sluggish and stable. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be kept in mind that the fork pointer should not touch other goods or items. The load needs to be supported with marginal back tilt of the gantry so that the tons does not move backwards. The pole can be slanted ahead slightly when the load is reduced to enable simple placement of the tons and removal of the forks. .
6. It is prohibited to fork items at broadband and ram hard things with the fork head. .
7. When the forklift is functioning, it is forbidden for individuals to loaf the fork, so as to avoid the collapse of the goods and hurt people. .
8. Overwhelming is restricted, and it is forbidden to utilize forks to raise personnel to engage in high-altitude operations to avoid high-altitude dropping mishaps. .
9. It is not permitted to utilize the brake inertia to slide, put, round or roll items. .
10. It is not permitted to use forks to choose, turn pallet discharge.

Leaving .
1. It is forbidden to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you should discharge the goods or reduced the fork frame.
2. Draw the hand brake deal with to dead or depress the parking brake switch.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the vehicle driver does not leave the automobile's line of sight and does not go beyond 1 minute).
4. Eliminate the trick. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the appearance needs to be examined, and gas, lubricating oil and air conditioning water need to be added.
2. Examine the safety efficiency of beginning, running and stopping.
3. Examine whether the lights and horn signals are complete and reliable.
4. Throughout the procedure of the forklift, check whether the pressure and temperature level are regular.
5. After the forklift is running, the external leakage must also be checked and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You must check before leaving the auto;.
2. When you run into a person before you throughout driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not go beyond 5 km/h;.
4. When driving, the low point of the cargo need to be 0.3 m ~ 0.4 m in the air;.
5. The turning ought to not be too sharp to prevent the tendency of "free turning";.
6. Adding and down the incline must be sluggish and uniform, and no activating the slope is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the car needs to be driven backwards when worsening;.
8. When the forklift workers carry the goods and move forward, if they experience large or hefty goods and most likely to the motorist's line of sight, they need to take the reversing workout
.
The "Eight Prohibitions" must be followed in the procedure.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not permitted to grab the goods by passing on the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not allowed to use inertia force to get the goods.
6. It is not permitted to make use of stopping pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring people to work with the pallet or fork, and it is strictly forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Car parking is not permitted under the following conditions.
1. Contours, slim roads, railway crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an obstacle on one side of the roadway, the contrary side of the section with the exact same length as the challenge should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844